Home
Operation
Example configurations for consumables
Consumables that are worn or have damage can have a bad effect on cut quality.
Non-ferrous (stainless steel and aluminum) example configurations
Use these sets of consumables to cut non-ferrous material. Stainless steel and aluminum are examples of non-ferrous metals.
Non-ferrous – 300 A – N₂/N₂, Mix/N₂, N₂/H₂O
N₂/H₂O can be used only with VWI™ and OptiMix™ consoles. Mix/N₂ can be used with OptiMix consoles.

Register your new Hypertherm system
Warranty information
Recycling information
Contact us
Safety information
Electromagnetic Compatibility (EMC)
Specifications
Qualifications and Requirements
Installation
Connect for Communication
Coolant Installation
Operation
- CNC controls and display
  A Computer Numerical Control (CNC) controls cutting system operation.
- Wireless device controls
  You can use a wireless device to set up and monitor the plasma cutting system.
- Power-indicator LEDs
  An Light Emitting Diode (LED) illuminates to show the power status on the plasma power supply and on other system components.
- Sequence of operation
  A set of flowchart images shows the sequence of operation for the plasma cutting system.
- Process selection
  All of the cutting processes have a process ID that is a unique identification number. Each process ID aligns with a set of preprogrammed values in the cut chart database in the plasma power supply control Printed Circuit Board (PCB).
- Cut charts
  A cut chart contains parameters that are necessary to get optimal results for your cutting process with special materials and thicknesses.
- Torch consumables
  The plasma cutting system uses the same consumable parts for perpendicular-position processes (90° angle) and bevel-cutting processes.
- Example configurations for consumables
  Consumables that are worn or have damage can have a bad effect on cut quality.
  - Ferrous (mild steel) example configurations
    Use these sets of consumables to cut ferrous material. Mild steel is an example of a ferrous metal.
  - Non-ferrous (stainless steel and aluminum) example configurations
    Use these sets of consumables to cut non-ferrous material. Stainless steel and aluminum are examples of non-ferrous metals.
    - Non-ferrous – 40 A – N₂/N₂ and Air/Air
    - Non-ferrous – 60 A – F5/N₂, N₂/N₂, N₂/H₂O, and Air/Air
      F5/N₂ and N₂/H₂O can be used only with VWI™ and OptiMix™ gas connect consoles.
    - Non-ferrous – 80 A – F5/N₂, N₂/N₂, N₂/H₂O, Air/Air
      F5/N₂ and N₂/H₂O can be used only with VWI™ and OptiMix™ gas connect consoles.
    - Non-ferrous – 130 A – N₂/N₂, Mix/N₂, N₂/H₂O
      F5/N₂ and N₂/H₂O can be used only with VWI™ and OptiMix™ gas connect consoles. Mix/N₂ can be used only with OptiMix gas connect consoles.
    - Non-ferrous – 170 A – N₂/N₂, Mix/N₂, N₂/H₂O, Air/Air
      N₂/H₂O can be used only with VWI™ and OptiMix™ gas connect consoles. Mix/N₂ can be used only with OptiMix gas connect consoles.
    - Non-ferrous – 300 A – N₂/N₂, Mix/N₂, N₂/H₂O
      N₂/H₂O can be used only with VWI™ and OptiMix™ consoles. Mix/N₂ can be used with OptiMix consoles.
- Recommendations for maximum consumable life
  Consumables are the parts of the torch that wear as they are used. Consumables that are near end-of-life can have a bad effect on cut quality and performance.
- Arc Response Technology
  Arc Response Technology™ lets the plasma cutting system adapt to problems at the torch that can cause decreased consumable life or possible torch damage.
Maintenance
Diagnostics and Troubleshooting
Parts List
Wiring Diagrams

Non-ferrous – 300 A – N₂/N₂, Mix/N₂, N₂/H₂O

N₂/H₂O can be used only with VWI™ and OptiMix™ consoles. Mix/N₂ can be used with OptiMix consoles.

This image shows a 300 A consumable set for non-ferrous cutting. — Figure 1. Non-ferrous 300 A consumables

1	Shield retaining cap
2	Shield¹
3	Nozzle retaining cap
4	Nozzle
5	Swirl ring^¹
6	Electrode
7	Water tube
¹ The bottom part number is for mirror cutting only.

Non-ferrous – 300 A – N2/N2, Mix/N2, N2/H2O

Non-ferrous – 300 A – N₂/N₂, Mix/N₂, N₂/H₂O